To size an LED strip power supply, multiply the strip wattage per meter by the installed length, then add an appropriate safety margin. For example, a 10-meter strip rated at 9.6 W/m requires 96 W. Using a 20% margin gives a minimum recommended capacity of about 115 W, so the next suitable standard power supply size should be selected.
Quick Formula
Required power supply capacity = watts per meter ร total meters ร safety factor
- Use 1.20 as a common 20% safety factor for many normal installations.
- Use the actual specification of the selected LED strip, not a generic wattage.
- Confirm voltage compatibility: a 24V strip requires a 24V constant-voltage power supply.
- Consider separate drivers or feed points when one installation contains long runs.
Power Supply Sizing Examples
| LED Strip Load | Calculation | Minimum With 20% Margin |
|---|---|---|
| 5 m ร 4.8 W/m | 24 W | 28.8 W |
| 5 m ร 9.6 W/m | 48 W | 57.6 W |
| 10 m ร 9.6 W/m | 96 W | 115.2 W |
| 10 m ร 14.4 W/m | 144 W | 172.8 W |
| 20 m ร 14.4 W/m | 288 W | 345.6 W |
Select a standard-rated power supply above the calculated minimum. Also verify the manufacturer’s permitted continuous load, installation temperature and ventilation requirements.
Step 1: Confirm Strip Voltage
The power supply output voltage must match the LED strip. Never connect a 12V strip to a fixed 24V output. For longer architectural runs, 24V is often selected because it carries the same power at lower current. Our 12V vs 24V LED strip guide explains the main differences.
Step 2: Find Watts per Meter
Check the exact model specification. Wattage varies with LED type, density, color, drive current and product tolerance. RGB or RGBW products may have different maximum consumption depending on which channels operate at full output.
Step 3: Calculate Total Connected Load
Multiply watts per meter by the length connected to the power supply. Include every branch powered by that driver. If several strip sections use one supply, add their loads together.
Step 4: Add Capacity Margin
A power supply should not normally operate continuously at its absolute rated limit. A margin can reduce thermal stress and provide allowance for product tolerance and operating conditions. Twenty percent is a common planning value, but the power supply manufacturer’s loading guidance has priority.
Step 5: Check Current and Cable Size
Current can be estimated using amps = watts รท volts. A 96 W load at 24V draws approximately 4 A, while the same power at 12V draws approximately 8 A. Cable length, conductor size, connector rating and allowable voltage drop must be considered.
Power Supply Size Does Not Solve Voltage Drop
A larger driver does not automatically deliver uniform brightness along a long strip. Voltage drop occurs in the strip PCB and supply cables. Long installations may require parallel feeds, power injection from both ends, shorter branches or multiple drivers.
Constant Voltage vs Constant Current
Most common flexible LED strips use constant-voltage power supplies, typically 12V or 24V DC. Constant-current drivers are used for different LED module designs and should not be substituted without confirming electrical compatibility.
Indoor, Outdoor and Dimming Considerations
- Choose an enclosure rating appropriate for the installation environment.
- Keep non-waterproof drivers away from moisture and condensation.
- Match the driver and controller to the required PWM, 0โ10V, DALI, TRIAC or other dimming method.
- Check inrush current when several drivers share one circuit.
- Provide ventilation and follow the required mounting clearances.
Information to Send for Power-Supply Matching
- Strip model, voltage and watts per meter
- Total length and length of each branch
- Cable distance from driver to strip
- Indoor, outdoor or wet-location environment
- Dimming and controller requirements
- Input voltage and destination market
- Required certifications and installation constraints
FAQ
Can I use a power supply with a higher wattage rating?
Yes, if the output voltage and electrical type are correct. The strip draws the power it requires; the supply rating describes its available capacity.
Why is the far end of my LED strip dimmer?
The usual cause is voltage drop along the PCB or cables. Shorter branches, heavier cable, 24V products or additional feed points may help.
Can one driver power multiple LED strip branches?
Yes, when the combined load, wiring, protection and controller capacity are correctly calculated. Parallel branch design is usually preferred over one excessively long series run.
